• 10/29/2020
  • Reading time 3 min.

Neutrons make structural changes in molecular brushes visible

Smart bottle brushes

They look like microscopic bottle brushes: Polymers with a backbone and tufts of side arms. This molecular design gives them unusual abilities: For example, they can bind active agents and release them again when the temperature changes. With the help of neutrons, a research team from the Technical University of Munich (TUM) has now succeeded to unveil the changes in the internal structure in course of the process.

Dr. Lester Barnsley, Instrumentwissenschaftler des Forschungszentrums Jülich, an der Kleinwinkelneutronenstreuanlage KWS-1 des Heinz Maier-Leibnitz Zentrums an der Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRM II) der Technischen Universität München. Wenzel Schürmann / TUM
Dr. Lester Barnsley, instrument scientist at Forschungszentrum Jülich, at the small-angle neutron scattering system KWS-1 of the Heinz Maier-Leibnitz Zentrum at the Heinz Maier-Leibnitz Research Neutron Source (FRM II) at the Technical University of Munich.

"The structure of the bottle-brush polymers, which are only nanometers in size, cannot be investigated using classical optical methods: It can be seen that an aqueous solution containing these polymers becomes turbid at a certain temperature. But why this is the case, and how the backbone and the side arms stretch out into in the water or contract, has not yet been clarified," reports Prof. Christine Papadakis.

There is a simple reason why scientists would like to know more about the inner life of bottle-brush polymers: The fluffy molecules, which consist of different polymer chains and abruptly change their solubility in water at a certain temperature, are promising candidates for a variety of applications. 

For example, they could be used as catalysts to accelerate chemical reactions, as molecular switches to open or close tiny valves, or as transport media for medical drugs – the molecular brushes could thus bring pharmaceuticals to a center of inflammation and, because the temperature is elevated there, release them directly at the site of action.

However, the basic prerequisite for using the brush molecules is that their behavior can be programmed: Theoretically, chemists can use a combination of water-soluble and water-insoluble building blocks to determine precisely at what temperature the polymers clump together and the liquid in which they were just dissolved becomes cloudy. "In practice, however, you have to know exactly how and under what conditions the structure of the polymers changes if you want to design smart brush molecules," explains Papadakis.

Neutrons reveal their molecular inner life

Together with her team in the Soft Matter Physics Group at the Technical University of Munich, she has now been able to visualize for the first time the changes that bottle-brush polymers with arms made of two different types of building blocks undergo when the temperature reaches the cloud point. 

The scientists used neutron radiation from the Research Neutron Source Heinz Maier-Leibnitz (FRM II) on the campus Garching in a special instrument for small angle neutron scattering, which is operated by the Forschungszentrum Jülich.

This method is particularly well suited for the investigation because neutrons are electrically neutral and therefore penetrate matter easily. There they are scattered by the atomic nuclei, which results in detailed information about the brush molecules. In combination with modern cryo electron microscopy, a detailed understanding of these molecules could be obtained.

When brushes clump together

The thermoresponsive brush molecules studied by Papadakis' team were synthesized by chemists from the National Hellenic Research Foundation in Greece and the Technische Universität Dresden, respectively. 

In the first step, the samples were dissolved in water, then gradually heated up to the cloud point and irradiated with neutrons. A detector monitored the scattered radiation. From the scattering signal, the researchers were able to deduce the structural changes.

Depending on the structure of the polymers, water molecules split-off already before the cloud point was reached. At the cloud point itself, the molecular structure of the polymers collapsed. What remained were water-insoluble polymer coils, which formed loose or compact clusters depending on the residual water content.

"The results will help to develop bottle-brush polymers suitable for practical use," the physicist is convinced. "If you know exactly how polymers change at the cloud point, you can optimize their chemical structure for different applications."

Publications

Jia-Jhen Kang, Kaltrina Shehu, Clemens Sachse, Florian A. Jung, Chia-Hsin Ko, Lester C. Barnsley, Rainer Jordan, Christine M. Papadakis:
A molecular brush with thermoresponsive poly(2-ethyl-2-oxazoline) side chains: a structural investigation
Colloid and Polymer Science, 05.08.2020

Jia-Jhen Kang, Florian A. Jung, Chia-Hsin Ko, Kaltrina Shehu, Lester C. Barnsley, Fabian Kohler, Hendrik Dietz, Junpeng Zhao, Stergios Pispas, and Christine M. Papadakis:
Thermoresponsive Molecular Brushes with Propylene Oxide/ Ethylene Oxide Copolymer Side Chains in Aqueous Solution
Macromolecules 2020, 53, 4068−4081, 14.08.2020

Further information and links

The work was done in cooperation with the Faculty of Chemistry and Food Chemistry of the Technische Universität Dresden and the Theoretical and Physical Chemistry Institute of the National Hellenic Research Foundation, Greece. The project was funded by the German Research Foundation.

Technical University of Munich

Corporate Communications Center

Contacts to this article:

Prof. Dr. Christine Papadakis
Professorship Soft Matter Physics
Technical University of Munich
James-Franck-Str. 1, 85748 Garching, Germany
Tel.: +49 89 289 12447
papadakisspam prevention@tum.de

Back to list

News about the topic

HSTS